Resilio sync ui install#

Ignore some files/folders synchronization This is easily fixed by mkdir ~/.rslsync, or whatever your storage_path is set to. If you start the service but cannot reach the WebUI, check the unit status for the system-wide instance or the user unit.Ī common error is Storage path specified in config file does not exist. This is done independently from the creation of the configuration file.

The script also creates the storage_path directory set in the configuration file if it does not exist. Rslsync_rvice creates ~/.config/rslsync/nf if it does not exist, and guesses some default values of the settings: Individual users can then enable the rslsync_rvice user unit. Although defeating most of its purpose, rvice can be disabled.

Resilio sync ui install#

The install script enables the service for all users by default. If your $UID is '1000', the port will be 8889. Rather than 8888, the port for the user's instance of rslsync will be 7889 + $UID. Note: If the configuration file was generated by rslsync AUR it will be configured with a different port. You will probably want to change some of the settings, including: # rslsync -dump-sample-config > ~/.config/rslsync/nf You should review the configuration settings especially user and password, see below.Ī sample configuration file can be created using: You can also run it as the rvice system user (without the -user flag).Ĭonfiguration for this user is located at /etc/nf, and metadata is saved in /var/lib/rslsync/ by default. If running rslsync on a headless server, enable lingering to start rslsync and keep it running outside user sessions: Systemd/User#Automatic start-up of systemd user instances.If the user permissions are correct but rslsync still fails to run after being enabled, restart your system. Failure to do so will prevent the service from running. are owned by the user invoking the command. It is important to make sure that when rslsync is run as the user, the nf file and directory where the rslsync.pid file will be located have the correct user permissions, i.e.Note that the above command is not run as root: doing so may lead to a cryptic error stating that D-Bus has refused the connection.

The service will run as the user invoking the command. When that is done, start and (if you want it to start on boot) start/enable the user service rslsync (i.e., with the -user flag). You will also need to create the storage_path directory. Once installed, you will first need to create a configuration file at ~/.config/rslsync/nf, see #Configuration. Shared folders can also be configured statically in a configuration file, but doing so disables the WebGUI. The Linux client of Resilio Sync does not use a typical GUI, instead it sets up a WebUI server accessible at localhost:8888. The rest of this guide assumes that you are using the rslsync AUR package. login id and password) to those files prior to enabling rvice.Īlternatively, the bare 'tar.gz' packaged executable can be downloaded from the official website. This package creates a default /etc/nf for system/root operation. The package includes systemd service definitions for managing the rslsync daemon. Rslsync AUR can be installed from the AUR. 4.4 Error while loading shared libraries: libcrypt.so.1.4.2 Ignore some files/folders synchronization.3.1 Automatic configuration file creation.The synchronization has no speed or size limits, as long as both devices have enough disk space. From now on, every device that wants to synchronize that folder must know the secret key. When a device adds a folder for synchronization, a secret is generated.

By handing over the 'secret', files and folders can be shared with other users. This key is derived from a 'secret' which itself is a random 21 Byte key Base32-encoded. If many devices are connected simultaneously, files are shared between them in a mesh networking topology.Īll traffic between devices is encrypted with AES-128 in counter mode, using a unique session key. The user's data is exclusively stored on the devices with which the user chose to be in sync with, hence it is required to have at least two user devices, or 'nodes' to be online. Instead of having a central server which archives every file, it uses peer-to-peer connections between the devices themselves therefore there is no limit on data storage and/or transfer speed. Resilio Sync (formerly: BitTorrent Sync or BTSync) is a proprietary file sharing system that relies on the BitTorrent Peer-to-peer (P2P) protocol.